Preheating Touch Screen SMD Rework Station

DH-B2 BGA Rework station is also provided with Alarm set point to increase the process safety and control. It is compatible for the lead free and leaded soldering. It provides the safe heating for all kinds of components like SMD, BGA, CBGA, CCGA, CSP, QFN, MLF, PGA and all epoxy non-defiled µBGA etc.

Send InquiryChat Now
Product Details

Preheating Touch Screen SMD Rework Station 


1. Product Features of Preheating Touch Screen SMD Rework Station


preheating touch screen smd rework station.jpg


1. BGA Rework Station made by Dinghua has 3 heaters (Upper Heater, Lower Heater and Bottom IR Heater). The upper and lower heaters heat directly towards BGA part to ensure BGA gets enough heat to reach the melting point to come to good welding quality. The bottom heating zone is large area IR heating board for preheating the whole PCB board to insure even heating and prevent the PCB get deformed.

2. the hot air part of the long-life use of imported heating wire, through a special heat insulation, heat evenly, and durable.

3. three-zone support design, support height can be adjusted to restrict the welding area to sink.

4. the upper adjustable air flow for different BGA chips use a different air flow, temperature more accurately, non-explosive bridge.


2.Specification of Preheating Touch Screen SMD Rework Station


hot air rework tool.jpg


3.Details of Preheating Touch Screen SMD Rework Station

1.HD Touch screen interface;  

2.Three independent heaters ( hot air & infrared );

3. Vacuum pen;

4.Led headlamp.



4.Why Choose Our Preheating Touch Screen SMD Rework Station? 



5.Certificate of Preheating Touch Screen SMD Rework Station


bga rework hot air.jpg


6.Packing & Shipment of Preheating Touch Screen SMD Rework Station


soldering infrared station.jpg

cheap reball station.jpg


7.Contact us


名片.jpg


8.Related knowledge

Precaution of installing BGA rework station

With the slowing of global economic growth and the gradual increase of labor costs, Industry 4.0 has a major global impact. The SMT surface mount technology and process requirements have also increased. Therefore, the degree of automation of the BGA rework station for the rework process in the entire industry has been improved. And the accuracy of repairs is also higher. Therefore, our company introduced the world's first fully automatic BGA rework station ZM-R8650, which has been applied to various companies in the industry. Zhuo Mao BGA rework station is widely used in the market, then we need to pay attention to what matters during installation and use? The following is a brief introduction:

BGA Rework Station Installation Notes:

1. During the installation, please do not place the BGA rework station on places where the air flow is large, and avoid the influence of lateral wind flow on the welding.

2, the installation of the desktop is flat, solid, uneven desktop, may cause deformation of the shell, noise, and line failure.

3. When the work area of ??the rework station is warmed up in a large area, the use of solder paste heating will cause a small amount of gas to evaporate. Please pay attention to the indoor ventilation (do not conflict with the first one). Our company also introduced a ZM-R6500BGA rework station with automatic air purification device, which is more convenient to use.

4. Pay attention to the power required to install the BGA Rework Station to avoid unnecessary losses due to circuit short-circuit caused by operational errors. In general, it is necessary to ensure that the wire is not less than 2.5 square meters and that the grounding is good.

5. Do not use too much dust in the space used in the rework station, otherwise it may accelerate the aging of the heating components.

Hot Tags: preheating touch screen SMD rework station, China, suppliers, manufacturers, price, for sale
Related Products
Inquiry
    Contact Us
  • +86-0755-29091833
  • Sales31@dinghua-bga.com
  • 4th Floor, Block 6B, Shengzuozhi Industrial Park, Xinyu Road, Shajin, Baoan, Shenzhen, China
    JOIN US